You are here

H3000 Sampler Board HS395 Installation

Login to Post to Forums

You must be logged in to the Eventide website in order to post to our forums. If you do not have an account, you will need to create one. You may also reset your password.

10 posts / 0 new
Last post
DSP4000
Joined: Mar 17 2012
Posts: 5

H3000 Sampler Board HS395 Installation

DSP4000
April 29, 2012 - 05:15 am

Hi,

Does anybody have any experience with installing the sampler board in the H3000?

I have scored a sampler board, but no mounting hardware or installation instructions. I have the H3500 Roms, so there's no issues with the OS or sampler algorithms.

I haven't directly asked Eventide about the instructions or mounting hardware yet, as I thought I'd try and find out as much as I could first before hassling them.

Cheers

nickrose's picture
Eventide Staff
nickrose
Joined: Jan 17 2008
Posts: 4640
nickrose
May 02, 2012 - 04:56 pm

Not a small thing, I'm afraid - may well require hardware mods to the motherboard.  Also, since this is now so old, there is little information we could give, even after hassling. Hopefully someone out there has the original installation instructions they can pass onto you (we don't).

DSP4000
Joined: Mar 17 2012
Posts: 5
DSP4000
May 02, 2012 - 08:03 pm

That is very disappointing.

Just one question - what instructions do you get with the HS395 sampler board that appears to be available in the Store?

nickrose's picture
Eventide Staff
nickrose
Joined: Jan 17 2008
Posts: 4640
nickrose
May 03, 2012 - 12:09 pm

You are way ahead of me - I didn't even know it was still listed. We have a few dusty boxes on the shelf, but they are sealed, so it is hard to know what is inside them. Don't think we are going to want to open them at this time.

nickrose's picture
Eventide Staff
nickrose
Joined: Jan 17 2008
Posts: 4640
nickrose
May 03, 2012 - 02:47 pm

You're in luck - I found an open one. Send a mailing address marked for my attention at support@eventide.com, and I'll get it off to you. Sorry, no electronic version.

But, before you start, be aware that this is a difficult modification, and if you get any problems, we won't be able to help indirectly - you would have to send it in for service.

AdamIEcho's picture
Check out my Eventide Gear
AdamIEcho
Joined: Feb 11 2014
Posts: 3
AdamIEcho (My Eventide Gear)
December 09, 2018 - 09:52 am

I have acquired a 90 second Sampler Board from a parted out H3500B-DFX.

I would like to install it on my maxed-out H3000SE (All eproms installed, cut and jumps completed).

Can someone provide me with an installation guide?

From what I can tell from seeing an H3500-DFX motherboard, there are 3 cuts, 8 jumps and the installation of a 40 pin male ribbon cable socket that my unit doesn't have.

Anyone with experience willing to contribute, your assistance will be greatly appreciated.

Thanks.

-Adam.

analogwizard
Joined: Jan 15 2021
Posts: 2
analogwizard
January 15, 2021 - 09:55 am

Hi

I would like to do the reverse and kick out the sampling board from a H3000 that is presently not runing :-(
I have all the schematic of the H3000 but not the additional schematic for the studio sampler board.
I can see the modification but would like to check with original docs for building it back as far as neccessary.
Hope anyone can share the Sampler installation docs. I can provide pictures of the mods if that is helpfull or copies
of the presently installed eproms.

analogwizard

AdamIEcho's picture
Check out my Eventide Gear
AdamIEcho
Joined: Feb 11 2014
Posts: 3
AdamIEcho (My Eventide Gear)
January 16, 2021 - 12:14 am

I've got everything you need -see if it's uploaded correctly.

Breathe, work slowly and patiently, and you'll get it done -This is where information becomes knowledge.

Good luck to you.

-Adam.

analogwizard
Joined: Jan 15 2021
Posts: 2
analogwizard
January 18, 2021 - 06:08 am

Hi Adam
got it thx, greate help :-)

AdamIEcho's picture
Check out my Eventide Gear
AdamIEcho
Joined: Feb 11 2014
Posts: 3
AdamIEcho (My Eventide Gear)
January 19, 2021 - 05:10 pm

I know what it's like -Glad to help.

-Adam.