You are here

Viewing HOTKNOB Patch Destinations (how?)

Login to Post to Forums

You must be logged in to the Eventide website in order to post to our forums. If you do not have an account, you will need to create one. You may also reset your password.

4 posts / 0 new
Last post
Check out my Eventide Gear
silver_mica
Joined: Nov 5 2015
Posts: 19

Viewing HOTKNOB Patch Destinations (how?)

(My Eventide Gear)
December 01, 2017 - 12:12 pm

I've been making a point of using the Eventide H9 without Control - I'm proficient with the basics such as bringing up Presets/Algorithms and adjusting parameters and a few other adjustments.  I'm learning to use the HOTKNOB right now - and noticed that I could not see what parameters are assigned to the HOTKNOB & Center dial while following these instructions from the H9 User guide (page 24 of my copy)

View HOTKNOB Patch Destinations

To view the list of parameters assigned as HOTKNOB patch Press and hold HOTKNOB button while holding down the X, Y or Z button. Use the Knob to scroll through the list of parameters names assigned to the HOTKNOB.

I've tried this procedure on several of the factory presets and did make sure to observe that the HOTKNOB & Center dial altered parameters first - before following the above instructions.  However when I attempt to view the HOTKNOB patch destinations I don't seen anything - except, briefly, the word "TURN" as I'm holding the HOTKNOB button while holding down X, Y or Z and slowly spinning the dial counterclockwise.     

Perhaps what I expect to see isn't what the above instructions are describing?  I am expecting to to see a list parameters assigned assigned to the HOTKNOB & Center dial (which should be the same as the expression pedal).   Is this a correct assumption?  

Aside, how does one see those parameters altered by the HOTKNOB & Center Dial?

David 

 

 

nickrose's picture
Eventide Staff
nickrose
Joined: Jan 17 2008
Posts: 3995

silver_mica wrote:

December 04, 2017 - 11:11 am

silver_mica wrote:

I've been making a point of using the Eventide H9 without Control - I'm proficient with the basics such as bringing up Presets/Algorithms and adjusting parameters and a few other adjustments.  I'm learning to use the HOTKNOB right now - and noticed that I could not see what parameters are assigned to the HOTKNOB & Center dial while following these instructions from the H9 User guide (page 24 of my copy)

View HOTKNOB Patch Destinations

To view the list of parameters assigned as HOTKNOB patch Press and hold HOTKNOB button while holding down the X, Y or Z button. Use the Knob to scroll through the list of parameters names assigned to the HOTKNOB. 

I've tried this procedure on several of the factory presets and did make sure to observe that the HOTKNOB & Center dial altered parameters first - before following the above instructions.  However when I attempt to view the HOTKNOB patch destinations I don't seen anything - except, briefly, the word "TURN" as I'm holding the HOTKNOB button while holding down X, Y or Z and slowly spinning the dial counterclockwise.     

Perhaps what I expect to see isn't what the above instructions are describing?  I am expecting to to see a list parameters assigned assigned to the HOTKNOB & Center dial (which should be the same as the expression pedal).   Is this a correct assumption?  

Aside, how does one see those parameters altered by the HOTKNOB & Center Dial?

Not quite sure why you are having a problem. For example, using preset 38 "DISA...".

Hold down "X" switrch. Then (without releasing) hold down "HOTKNOB" switch. Display shows "TURN". Turn knob - display shows "SLURM","PDLY","TAPS","LENGTH", "MIX", which is the list.

 

Check out my Eventide Gear
silver_mica
Joined: Nov 5 2015
Posts: 19

How to display HOTKNOB Parameter list

(My Eventide Gear)
December 04, 2017 - 12:19 pm

Not sure why, but when I try I'm unable to show the list of parameters that are tied to the HOTKNOB (and expression pedal).  I made an unlisted YouTube video showing my attempts. 

https://youtu.be/AQEYKoJ-R20

nickrose wrote:

Not quite sure why you are having a problem. For example, using preset 38 "DISA...".

Hold down "X" switrch. Then (without releasing) hold down "HOTKNOB" switch. Display shows "TURN". Turn knob - display shows "SLURM","PDLY","TAPS","LENGTH", "MIX", which is the list.

Check out my Eventide Gear
silver_mica
Joined: Nov 5 2015
Posts: 19

How to display HOTKNOB Parameter list?

(My Eventide Gear)
December 10, 2017 - 10:33 am

bump

silver_mica wrote:

Not sure why, but when I try I'm unable to show the list of parameters that are tied to the HOTKNOB (and expression pedal).  I made an unlisted YouTube video showing my attempts. 

https://youtu.be/AQEYKoJ-R20

nickrose wrote:

Not quite sure why you are having a problem. For example, using preset 38 "DISA...".

Hold down "X" switrch. Then (without releasing) hold down "HOTKNOB" switch. Display shows "TURN". Turn knob - display shows "SLURM","PDLY","TAPS","LENGTH", "MIX", which is the list.