Reverb_D delay clarification

Home Forums Products Vsig and Preset Development Reverb_D delay clarification

  • This topic is empty.
Viewing 2 reply threads
  • Author
    Posts
    • #115868
      eventidesurf
      Member
      Hello everyone,

       

      I have a few questions on Reverb_D:

       

      How do the delays work? Example:

      L   R   L    R

      10 20 30 40

       

      Is that absolute, or is 30 actually 30+10, and 40, 40+20?

       

      If absolute, then on Italos ‘plate’:

       

      75.7 83.1 90.3 93.9 94.3 78.6 108.8 114.0 157.2 134.2 141.9 123.1

       

      Could also be:

       

      75.7 78.6 90.3 83.1 94.3 93.9 108.8 114.0 141.9 123.1 157.2 134.2

       

      Note: I just sorted L/R channels.

       

       

      Also,

       

      Does the first delay matter? Can it be set to 0 and use ‘predelay’ to shift delays over? Is it customary to use something over 5, 10, 15?

       

      Any tips to simulate plates, halls, rooms, etc? Note: I know diffusion has a lot to do with that.

       

    • #154607
      DGillespie
      Moderator
      Eventide Staff

      Hi eventidesurf,

      The Reverb_D module uses what is often called a Feedback Delay Network (FDN) structure.  In this structure the delays aren't left and right, but they're all in parallel with a large feedback matrix which controls how they're fed back.  If you're interested in a good introduction to FDNs you can check out Julius O Smith's page on the topic (https://ccrma.stanford.edu/~jos/pasp/FDN_Reverberation.html)

      So the delays aren't really left and right, and because of the matrix the order does matter.  You can obviously sort the delays that way, and the reverb will probably sound similar, but different.

      A full reverb would usually be built by adding a multitap delay module, like multitap or easytaps to simulate early reflections, followed by some diffusors, like the diffusor module, then a Reverb_D, then maybe some EQs for the output.  Setting the delays lengths and feedback values tends to be a dark art, and honestly my approach is usually just to fiddle with it until it sounds good.

    • #154608
      DGillespie
      Moderator
      Eventide Staff

      You can also look at the existing Reverb programs in the H9000 and look at what was done for a primer.

    • #154610
      eventidesurf
      Member
      DGillespie wrote:

      Hi eventidesurf,

      The Reverb_D module uses what is often called a Feedback Delay Network (FDN) structure.  In this structure the delays aren’t left and right, but they’re all in parallel with a large feedback matrix which controls how they’re fed back.  If you’re interested in a good introduction to FDNs you can check out Julius O Smith’s page on the topic (https://ccrma.stanford.edu/~jos/pasp/FDN_Reverberation.html)

      So the delays aren’t really left and right, and because of the matrix the order does matter.  You can obviously sort the delays that way, and the reverb will probably sound similar, but different.

      A full reverb would usually be built by adding a multitap delay module, like multitap or easytaps to simulate early reflections, followed by some diffusors, like the diffusor module, then a Reverb_D, then maybe some EQs for the output.  Setting the delays lengths and feedback values tends to be a dark art, and honestly my approach is usually just to fiddle with it until it sounds good.

      I was afraid it was going to be more complicated. Italo’s plate and chamber seem to be a bit vibey, even if I reduce the first delay down to 15 and shift the rest of the delays down evenly, then increase rsize to compensate. If you use more consistent delays, such as one of the other presets from Italo (I’m using H8000FW btw):

      15.0 22.0 30.0 39.0 50.0 60.0 78.0 90.0 120.0 135.0 158.0 166.0

      The reverb sounds smoother, but somewhat less dimensional, less bloom.

      I’m using stereo taps to simulate ERs. Unfortunately the other modules were buggy when I tried them. I do use an EQ also. Thanks for the link!

       

Viewing 2 reply threads
  • You must be logged in to reply to this topic.